No student devices needed. Know more
37 questions
Which form will you use as a guide throughout the vehicle inspection process?
AF Form 1800, Operator’s Inspection Guide and Trouble Report.
AF Form 1474, Agency Report of Motor Vehicle Data.
AF Form 1823, Vehicle and Equipment Work Order.
AF Form 2028, Vehicle Unit Inspection Record.
Which action would you complete when conducting a before-operation inspection of a
vehicle?
Listen for unusual noises.
Check all the lights and instrument panel.
Ensure the brakes and mechanical parts are operating properly.
Review the AF Form 1800, Operator’s Inspection Guide and Trouble Report, for open discrepancies.
The purpose of the before-operation vehicle inspection is to ensure
the vehicle control officer is adhering to regulations.
no one has driven the vehicle since you last inspected it.
the vehicle is safe and in commission before you operate it.
all damage and malfunctions are recorded before you report it.
In which part of a vehicle inspection will you turn off the engine, place the chocks, and walk around the vehicle to check for leaks, tire pressure, and any damage that may have occurred during use?
Before operation.
During operation.
After operation.
This does not occur during any part of the inspection.
Which information are you required to put in the designated shift/signature block of the AF Form 1800, Operator’s Inspection Guide and Trouble Report, once you complete the inspection?
Full name only.
Last name only.
Laundry mark only.
Last name and rank only.
When you are performing a before-operation inspection on a forklift, open the hood and check for
damage and leaking muffler and exhaust system.
serviceability of the fire extinguisher.
serviceability of the tow connections.
security of the battery terminals.
Which fluid level would you check when performing a during-operation inspection on a 10K forklift?
Oil.
Brake.
Hydraulic.
Transmission.
Which forklift has a maximum lifting capacity of 10,000-pounds and can lift up to 150 inches high?
4K.
10K.
10K AT.
50K.
When approaching the ramp for final positioning, what feature of the 10K forklift should you use to have smooth, positive control?
Inching pedal.
Rollerized tines.
Mast control lever.
Highest forward gear.
Which forklift is designed for operating on rough terrain?
4K.
6K.
10K.
10K AT.
When is it safe to raise or lower a load on a forklift?
Anytime.
Only after you’ve come to a complete stop.
Only after you’ve secured the pallet to the tines.
Only after you’ve ensured there is no one near the tines.
Which K-loader can hold up to six 463L pallets and has a loading capacity of 60,000 pounds?
25K.
40K.
Tunner loader.
Halvorsen loader.
Which deck function is unique only to the Tunner loader?
Pitch.
Shift.
Roll.
Yaw.
Which cab controls on the Tunner are used to operate the deck functions when on/offloading cargo?
Circuit breaker panel.
Deck pitch control box.
Deck and conveyor control panel.
Primary deck control indicator light.
With four fully charged batteries, the emergency standby system on the Tunner will provide normal steering, lift, and hydraulic functions on a limited basis for about how many minutes?
30.
40.
50.
60.
Operating the starter continuously on the Tunner for longer than a minimum of how many seconds will cause it to overheat?
20.
30.
60.
120.
After cranking the starter on the Tunner for 30 seconds without a successful start, allow the starter to cool down for how many minutes before trying again?
1.
2.
3.
4.
The Halvorsen loader was designed to deploy within how many minutes?
20.
30.
45.
60.
Which K-loader has a deck range up to 225 inches and has adjustable pallet guides to accommodate pallets on the 88 or 108 inch side?
25K.
40K.
Tunner loader.
Halvorsen loader.
In case of an engine failure or hydraulic pump failure while driving, the Halvorsen has an electrically powered hydraulic pump within the hydraulic system that instantly and automatically operates for how many seconds?
20.
30.
45.
60.
If you were working as part of a loading crew, at which of these heights would you be required to wear a fall restraint harness?
4 feet.
5 feet.
8 feet.
11 feet.
When bridging K-loaders, in what position must the loaders be when transferring pallets between two loaders?
Lowered.
Pitched.
Raised.
Rolled.
In which part of a vehicle inspection will you clean and refuel the bus, if necessary, and ensure passengers did not damage any part of the bus interior?
Before operation.
During operation.
After operation.
Accomplishing this task is not necessary.
Which feature of the C–5 staircase truck provides initial positioning ability?
Hydraulic boom cylinders.
Prongs and pawl latches.
Top platform assembly.
Extension platform.
Which feature of the C−5 staircase truck allows you to more easily view the aircraft doorsill and pawl latches while raising the stairs?
Hydraulic boom cylinders.
Prongs and pawl latches.
Top platform assembly.
Window.
Which feature of the latrine service truck (LST) pumps chemicals into the lavatory tank to neutralize solids and eliminate odor?
Flush/recharge hose.
Dump valve.
Sight gauge.
Waste tank.
How do you know when the waste tank on the latrine service truck (LST) is full?
Open the tank and look inside.
Look through the sight window.
Wait until the flow meter zeroes out.
Look at the gauge in the control panel.
Which feature of the latrine service truck (LST) measures the amount of rinse-fill solution being pumped inside of an aircraft or Air Transportable Galley/Lavatory (ATGL)?
Flow meter.
Dump meter.
Control panel.
Waste tank sight gauge.
How many ounces of 5 percent sodium hypochlorite solution will you use on the potable water truck (PWT) for a 250-gallon tank?
24.
44.
64.
84.
Before operating the water pump on the potable water truck (PWT), ensure the tank contains at least how many gallons?
20.
40.
60.
80.
Passengers will not ride on the warehouse tug unless
there are no other vehicles to transport them.
a suitable seat with a back and side guard is installed.
they are able to be sufficiently buckled on the vehicle.
you request a waiver through you vehicle control officer.
Which vehicle can you not use to tow trailers or push equipment unless the manufacturer designates it for that operation?
Forklift.
Lox cart.
Warehouse tug.
Maintenance stand.
How many vehicle lengths should you keep between you and the vehicle in front of you when towing an item?
One.
Two.
Three.
Four.
What towing mistake can easily bend or break trailer tongues and render the equipment inoperable?
Jack-knifing.
Stopping too gradually.
Accelerating gradually.
Driving too close to the edge of a dock.
If you can raise the jaw of a pintle hook assembly when the latch is down, the latch
is not functioning properly.
needs a cotter pin inserted.
is functioning as required.
needs to be pried open.
Which part of a pintle hook assembly will be used in all pintle hook towing operations?
Tow valve.
Support legs.
Safety/cotter pin.
Integral brake system.
Once you have made the trailer connection to the pintle hook assembly, do not
insert the cotter pin.
lower the upper jaw.
step over the tow bar.
ensure the upper jaw will not open.
Explore all questions with a free account