Have an account?
Skip to Content
Build your own quiz
Suggestions for you
50 questions
Show Answers
See Preview
- 1. Multiple Choice
A measuring tool used to layout an angle or an arc.
Compass
Divider
Protractor
Tape Ruler
- 2. Multiple Choice
Its main purpose is to reproduce, reduce or enlarge the dimension of size on a drawing.
Ruler
Triangle
Triangular Scale
Tape Ruler
- 3. Multiple Choice
It is used for drawing vertical and oblique lines.
Ruler
Scale
Triangle
T-Square
- 4. Multiple Choice
This is used as guide in drawing horizontal lines.
Ruler
Scale
Triangle
T- Square
- 5. Multiple Choice
This instrument is used to draw circles, arcs, radii, and parts of many symbols.
Compass
Divider
Protractor
Tape Ruler
- 6. Multiple Choice
It helps a drafter keep the proportions accurate
Ruler
Scale
Triangle
T- Square
- 7. Multiple ChoiceWhat is this Drafting Tool?30-60-90 Triangle45 TrianglePlastic SlopeRight Triangle
- 8. Multiple ChoiceWhat is this Drafting Tool?30-60-90 Triangle45 TrianglePlastic SlopeRight Triangle
- 9. Multiple ChoiceWhat is this Drafting Tool?Metal TemplateStencilEraser ShieldFrench Curve
- 10. Multiple ChoiceWhat is this Drafting Tool?RulerTri-RulerScaleStraight Edge
- 11. Multiple ChoiceBreak LineCenter LineDimension LineHidden Line
- 12. Multiple ChoiceBreak LineCenter LineDimension LineHidden Line
- 13. Multiple ChoiceBreak LineCenter LineDimension LineHidden Line
- 14. Multiple ChoiceWhen placing views on a drawing, which view is above the front view?SideRightTopOrtho
- 15. Multiple ChoiceAngular dimensions are expressed in ___________.decimal inchesfractional inchesmillimetersdegrees
- 16. Multiple Choice
Which are the three views most common in orthographic drawing?
Front, top and bottom
Front, top, side
Top, side and bottom
Front, back and top
- 17. Multiple ChoiceWhat angle are lines in Isometric drawn at in relation to the bottom of the page?45603025
- 18. Multiple ChoiceHow many views are usually shown in an orthographic projection?3 views6 views9 views11 views
- 19. Multiple Choice
Select the correct orthographic view for A?
1
2
10
6
- 20. Multiple Choice
Select the correct isometric view for 11?
K
B
F
D
- 21. Multiple Choice
The distance at the red arrow is:
1.3 inches
1 3/16"
1 5/16"
1 1/4"
- 22. Multiple Choice
How do you convert a fraction to a decimal?
you can't
divide the numerator by the denominator
times the numerator by the denominator
subtract the numerator by the denominator
- 23. Multiple Choice
The decimal equivalent for 1/2" is .50
true
false
- 24. Multiple ChoiceThe front view shouldShow the most visible featuresBe above the right viewBe the back viewBe the view you like best
- 25. Multiple ChoiceTwo adjacent views have _____ dimension(s) in common.onetwothreefour
- 26. Multiple ChoiceWhen locating views on a drawing, the top view should be placed ____ the front view.to the left ofto the right ofabovebelow
- 27. Multiple ChoiceA multiview drawing will always require at least ____ orthographic views.onetwothreefour
- 28. Multiple ChoiceA view showing the true length and true width of an angular (inclined) surface.Auxiliary ViewTrue FaceForeshorteningPrimary View
- 29. Multiple ChoiceA two-point perspective drawing is also known as a(n) ____ perspective.angularhorizontalparallelvertical
- 30. Multiple ChoiceHorizontal axes in isometric drawings are drawn at _______ degrees.453012015
- 31. Multiple ChoiceWhich of the four Inventor Base environments and file extension names is .idw?PartAssemblyDrawingPresentation
- 32. Multiple Choice
What tool could you use to add depth to a created sketch?
Circle
Line
Extrude
Rectangle
- 33. Multiple Choice
In Autodesk Inventor, which tools can you use to view your design from any angle?
Revolve
Orbit
View Cube
Finish Sketch
- 34. Multiple Choice
What should you press if you want to exit a command in Inventor?
Exit
Delete
Enter
Escape
- 35. Multiple Choice
Which file type is used to create a new part?
Standard.iam
Standard.idw
Standard.ipn
Standard.ipt
- 36. Multiple ChoiceWhich navigation tool allows for lateral movement (left, right, up, or down) within the graphics window?zoompanscalerotate
- 37. Multiple ChoiceThe purpose of the middle mouse button or wheel is to ___________.bring up additional options.select points, navigation menus, and enter commands.change the drawing magnification and move around the drawing.serve as an alternative to the ENTER key.
- 38. Multiple Choice
What is the definition of a "constraint" in inventor?
Restrictions and associations that are applied to 2D geometry (shapes, points, lines) to make them line up or connect in a certain way
The limits and restrictions a designer must consider at the beginning of a project
Devices that keep a person from moving
Specifications for the size of a design, 2D or 3D
- 39. Multiple Choice
Autodesk Inventor software's primary purpose is?
Designing 3D House Plans
Designing 2 D House Plans
Designing 2D Mechanical Parts
Designing 3D Mechanical Parts
- 40. Multiple ChoiceWhat must you do first before you can create a 3D object?create 2D sketchclick extrudetype in measurementnone of the above
- 41. Multiple Choice
What tool will turn a 2D sketch into a 3D object by turning it around an axis?
Extrude
Revolve
Tangent
Ribbon
- 42. Multiple Choice
A line or plane that just barely touches a curved surface at only one point is the ____________________. 🤔
Horizontal
Tangent
Vertical
Nonexistent
- 43. Multiple ChoiceWhen the cursor moves over an endpoint or midpoint of an object, Inventor® informs you by displaying a _________.blue Xgreen dotred rectangleblue square
- 44. Multiple ChoiceWhat is the feature of the user interaction does this image portray?BrowserGraphics WindowQuick Access Tool BarRibbon
- 45. Multiple ChoiceWhich Autodesk Inventor command will create this vase?RevolveSweepExtrudeRotate
- 46. Multiple ChoiceWhich Autodesk Inventor command will create the 3D object?RevolveSweepCoilPattern
- 47. Multiple ChoiceWhich Autodesk Inventor command will create the 3D image in red?ExtrudeCopyMirrorMagic
- 48. Multiple ChoiceWhich Autodesk Inventor command will create the blue feature on the 3D part?roundfilletsweepcut
- 49. Multiple Choice
This is a _______________ dimension.
diameter
radius
linear
aligned
- 50. Multiple Choice
This is the symbol for:
perpendicular
diameter
radius
tangent
- Answer choicesTagsAnswer choicesTags