Safety Quiz- Shop tools
Save
Edit
Start a multiplayer game
Play LiveLive
Assign HW
Solo Practice
Practice
Preview (20 questions)Show answers
  • Question 1
    120 seconds
    Report an issue
    Q.

    What safety equipment are you required to wear when operating power tools?

    answer choices

    Eye protection

    Ear protection

    Closed toed shoes

    All of the above

  • Question 2
    120 seconds
    Report an issue
    Q.

    What should you do with jewelry, lanyards, and loose clothing before working with power tools?

    answer choices

    Push them back and out of the way

    Take them completely off

    Just be careful as you work

    Put the jewelry and lanyard into the loose clothing

  • Question 3
    120 seconds
    Report an issue
    Q.

    How do you clean up after using shop power tools?

    answer choices

    Sweep up saw dust

    Throw away scrap pieces

    Put away tools in their proper home

    All of the above

  • Question 4
    45 seconds
    Report an issue
    Q.

    Never wear headphones into the shop because...

    answer choices

    you will be changing your playlist and not looking at the blade

    you will not hear directions from the teacher

    you will miss important sounds coming from your tools

    all of the above

  • Question 5
    120 seconds
    Report an issue
    Q.

    What is the difference between a band saw and a scroll saw?

    answer choices

    Table Saw can turn sharp corners

    Scroll Saw can turn sharp corners

    Band saw can't make any turns

    Table saw only cuts thin pieces of wood

  • Question 6
    120 seconds
    Report an issue
    Q.

    How do you change bits in a drill?

    answer choices

    Change the drill direction to "forward" and turn on power

    Pull out the bit and put a new one in

    Loosen the chuck, place a new bit, and tighten

    Place chuck on table height adjustment. Turn on lasers

  • Question 7
    120 seconds
    Report an issue
    Q. What are the "teeth" of a power tool?
    answer choices
    The tiny blades of the saw blade
    The button to power on and off the tool
    The shield or protection from the blade
    The piece that you plug in
  • Question 8
    120 seconds
    Report an issue
    Q.

    Before drilling, what should you do with the wood stock and table?

    answer choices

    Push the bit into the wood to make it stand

    Clamp the wood to the drill bit chuck key

    Clamp the wood down to the table after adjusting height and alignment of table

    Align the wood with the laser to make sure the bit is lined up properly

    Drill baby drill

  • Question 9
    30 seconds
    Report an issue
    Q.

    What is a "fence" of a power tool.

    answer choices

    The button to power on and off the tool

    The shield or protection of the blade

    A wall to push wood against to cut a straight line

    The piece that you plug in

  • Question 10
    45 seconds
    Report an issue
    Q.

    Where should your non dominant hand be when working with the jigsaw, circ saw, and drill?

    answer choices

    Not touching the tool at all

    On the top/back helping push the tool

    Underneath the tool near the teeth

    Holding the cables of the tool

  • Question 11
    30 seconds
    Report an issue
    Q.

    The tool that loosens the drill chuck is the_____

    answer choices

    chuck wagon

    chuck key

    chuck taylor

    up chuck

  • Question 12
    30 seconds
    Report an issue
    Q.

    What does the "guard" of a power tool?

    answer choices

    A wall to push wood against to cut a straight line

    The tiny blades of a saw blade

    The piece that you plug in

    The shield or protection of the blade

  • Question 13
    30 seconds
    Report an issue
    Q.

    Here is a Jig Saw that is a hand held curve cutter. Which tool is the permanent version of a jig saw?

    answer choices

    Scroll Saw

    Table Saw

    Radial Saw

    Miter Saw

  • Question 14
    30 seconds
    Report an issue
    Q.

    When should you measure and mark the wood you are cutting?

    answer choices

    Measure the wood as you are cutting

    Cut the wood, then measure it

    Put the wood on the tool, then measure and mark.

    Measure, mark, then go to the tool to cut

  • Question 15
    120 seconds
    Report an issue
    Q.

    How fast should the blade be moving before cutting the wood?

    answer choices

    Cut the wood as soon as you turn on the tool

    Turn on the tool, wait 30 seconds, then cut

    Wait until full speed, and then cut

    Roughly 45 miles per hour

  • Question 16
    20 seconds
    Report an issue
    Q.

    When do you turn off the saw when cutting wood?

    answer choices

    At the end of the measurement while the saw is still in the wood

    Once the saw is completely out and away from the wood

    The saw turns off by itself

    Leave it on for the next persons using it

  • Question 17
    30 seconds
    Report an issue
    Q.

    Hand tools: When using force on tools with sharp blades, always

    answer choices

    pull towards you

    push tool away from fingers

    have a friend hold the piece

    wear gloves

  • Question 18
    20 seconds
    Report an issue
    Q.

    When measuring material to be cut, it is advisable to >>>

    answer choices

    Use the metric system

    measure once, cut twice

    measure twice, cut once

    cut until it is long enough

  • Question 19
    30 seconds
    Report an issue
    Q.

    After each tool use, remember to

    answer choices

    put the tool away

    clean up the dust with a broom

    place scraps in proper bin or throw scraps out

    report any tool malfunctions

    all of the above

  • Question 20
    20 seconds
    Report an issue
    Q.

    Sweep the floor with a

    answer choices

    cush blume

    sweep'in'izer

    dusty bustem

    push broom

    push bloom

Report an issue
Why show ads?
Report Ad
Join a game