An introduction to Arduino
3 years ago
masters
Save
Edit
Host a game
Live GameLive
Homework
Solo Practice
Practice
16 QuestionsShow answers
  • Question 1
    30 seconds
    Q. A micro-controller is...
    answer choices
    small CPU made of transistors and conductors of heat and sound sensor
    portable circuits capable of making other circuits
    small computer on a single integrated circuit containing a processor core, memory, and programmable input/output peripherals
    small chip made of silver
  • Question 2
    30 seconds
    Q. What does GPIO stand for?
    answer choices
    General Purpose Inner Outer Propeller
    General Purpose Input Output Pins
    General Purpose Interested Old People
    General Purpose Input Output Processor
  • Question 3
    30 seconds
    Q. Identify this component
    answer choices
    Uno Cards
    Arduino Duo board
    Raspberry Pi
    Arduino Uno board
  • Question 4
    30 seconds
    Q. Identify this component
    answer choices
    Arduino Uno board
    Breadboard
    Raspberry Pi
    White Plastic
  • Question 5
    30 seconds
    Q. What does IDE stand for?
    answer choices
    In Deep Environment
    Integrated Development Environment
    Internal Deep Escape
    IDE
  • Question 6
    30 seconds
    Q. How do you tell (give instructions) on what the Arduino board should do in an IDE?
    answer choices
    Editor
    Sketches
    Console
    IDE error
  • Question 7
    30 seconds
    Q. Before your program “code” can be sent to the board, it needs to be converted into instructions that the board understands. This process is called...
    answer choices
    Stop
    Compile
    Create Sketch
    Serial Monitor
  • Question 8
    30 seconds
    Q. This shows you what the IDE is currently doing and is also where error messages display if you make a mistake in typing your program. (often called a syntax error)
    answer choices
    Sketch Editor
    Text Console 
    Line Number
    Serial Monitor
  • Question 9
    30 seconds
    Q. This shows you what line number your cursor is on. It is useful since the compiler gives error messages with a line number
    answer choices
    Sketch Editor
    Text Console 
    Line Number
    Serial Monitor
  • Question 10
    30 seconds
    Q. A function is a series of programming statements that can be called by name. Which command is called once when the program starts:
    answer choices
    loop()
    setup()
    (output)
    (input)
  • Question 11
    30 seconds
    Q. A function is a series of programming statements that can be called by name. Which command is called repetitively over and over again as long as the Arduino has power.
    answer choices
    loop()
    setup()
    (output)
    (input)
  • Question 12
    30 seconds
    Q. A function is a series of programming statements that can be called by name. Which command delays the LED by a number of milliseconds is.
    answer choices
    loop()
    setup()
    delay()
    stop()
  • Question 13
    30 seconds
    Q. What does this sketch do?
    answer choices
    This sets up the pin that our LED is connected to as an OUTPUT pin.
    This sets up the pin that our LED is connected to as an INPUT pin
    This sets up and LED to turn off
    Turns the LED off by writing LOW out on the pin.
  • Question 14
    30 seconds
    Q. If we start by writing HIGH out on the pin connected to the LED. What will it make the LED do? (HIGH means putting 5V out on the pin)
    answer choices
    Turn the LED on
    Turn the LED off
  • Question 15
    30 seconds
    Q. If we start by writing LOW out on the pin connected to the LED. What will it make the LED do? (LOW means putting 0V out on the pin)
    answer choices
    Turn the LED on
    Turn the LED off
  • Question 16
    30 seconds
    Q. It starts with a /* and continues until a */  What does this do?
    answer choices
    Loads a sketch
    Makes comments
    Compiles quicker
    Makes stars appear
Report Quiz
Join a game